SDS Section 1: Identification, and the U.S. Address Rule

Valenc logo and the title: SDS Section 1: Identification, and the U.S. Address Rule

SDS Section 1 identifies the product and the party responsible for it. OSHA Appendix D, Table D.1 requires five items: the product identifier, other means of identification, the recommended use and restrictions on use, the name, U.S. address and U.S. telephone number of the responsible party, and an emergency phone number.

Section 1 is the shortest part of the SDS and serves as the link to all other sections. The product identifier connects the SDS to the label and the employer’s chemical inventory. Contact details determine who responds in case of an incident. Issues often arise with imported products or when information changes after the SDS is prepared.

For a complete overview, refer to our guide covering all 16 sections of an SDS.

The working rule

Section 1 names one product and one responsible party in the United States. The product identifier is identical to the label. The name and address match the label. Every phone number is a U.S. number that someone answers.

What goes in SDS Section 1

ItemWhat Appendix D requiresWhat the reviewer checks
(a)Product identifier used on the labelThe same name or number as on the shipped label, character for character.
(b)Other means of identificationProduct codes, synonyms and trade names a customer might search by.
(c)Recommended use of the chemical and restrictions on useUses that fit the handling advice in Section 7 and the controls in Section 8.
(d)Name, U.S. address and U.S. telephone number of the chemical manufacturer, importer or other responsible partyA current legal name, a U.S. address and a U.S. number that is answered.
(e)Emergency phone numberA U.S. number that can give emergency information on this product.

The product identifier must match the label

29 CFR 1910.1200 defines the product identifier as the name or number used for a hazardous chemical on a label or in the SDS. It has to permit cross-references among three things: the label, the SDS, and the list of hazardous chemicals in the employer’s written hazard communication program.

This is why “close enough” is insufficient. If the label, SDS, and purchasing system each use different names, workers cannot determine which SDS applies. OSHA’s inspection directive requires the product identifier on the label to match the SDS.

Variations should be listed under item (b), other means of identification. Include the product code, common synonyms, and any previous trade names there. Item (a) should remain identical to the label.

Item (c) is often limited to a single word or simply states “industrial use,” but it should provide more detail. The recommended use informs readers about the exposures considered in the SDS, while restrictions clarify what was not evaluated. Both should align with the handling advice in Section 7 and exposure controls in Section 8. For example, if Section 1 recommends spray application but Section 8 omits inhalation controls, there is a gap.

The responsible party: a U.S. name, address and telephone number

HazCom 2024 requires a “U.S. address” and “U.S. telephone number” in Appendix D. The label requirement in 1910.1200(f)(1) uses the same language. The responsible party is defined as someone who can provide additional information on the hazardous chemical and appropriate emergency procedures, if needed.

OSHA’s inspection directive for HCS 2024, effective May 19, 2026, adds the practical detail:

  • The name and address must be the same on the SDS and the label.
  • The U.S. address can be a mailing address or the company’s physical location. A P.O. Box is acceptable.
  • The U.S. telephone number has to be reachable, and the person who answers must be able to respond to questions in English.
  • It does not have to be a 24-hour number.

A contracted company, such as an SDS service or call center, may be listed as a contact but cannot assume the responsible party role. OSHA’s 2018 letter of interpretation states that the manufacturer or importer remains the responsible party and retains compliance responsibility.

Importers: the first U.S. business is the responsible party

Section 1 requires particular attention for importers. The standard defines the importer as the first U.S. business with employees that receives hazardous chemicals produced abroad for supply to domestic distributors or employers. OSHA’s 2018 letter clarifies the following requirements:

  • A foreign address cannot serve as the responsible party’s address, and a foreign phone number cannot serve as its phone number.
  • The company that imports the product becomes the responsible party. That holds even when the product is used only in the importer’s own facility.
  • The importer must make sure the SDS complies, which includes classifying the chemical and developing or obtaining a compliant SDS.
  • The foreign manufacturer’s details can stay, as supplemental information in Section 1 if they will not cause confusion, or in Section 16.
  • An SDS from an overseas supplier can be used if it meets the HazCom requirements. It still needs the U.S. details in Section 1.

OSHA adopted this position in 2018 under the 2012 standard, and the 2024 rule incorporated it into Appendix D. This requirement is effective now and does not wait for the 2027 mixtures deadline.

The emergency phone number

Appendix D requires an emergency phone number but provides no further details. The following two points address this gap.

It has to be a U.S. number. OSHA’s 2018 letter answers that question with a yes.

OSHA does not specify required hours for the emergency number. The standard does not require the Section 1 emergency number to be available 24/7. If your number is not staffed at all times, indicate this on the SDS and provide the available hours to prevent confusion during an emergency.

Transport regulations have stricter requirements. Under 49 CFR 172.604, shippers of hazardous materials must provide an emergency response telephone number on shipping papers. This number must be monitored at all times during transportation by someone knowledgeable about the material or who can immediately contact such a person. Answering machines or callback services do not qualify. Exceptions apply for limited quantities and certain shipments. Many companies use a single number that meets DOT requirements for both purposes. If you provide two numbers, clearly specify their purposes. Refer to our guide on SDS Section 14 for transport details.

A worked review: an imported raw material

A hypothetical U.S. blender buys a resin from a European producer and resells part of it. The producer’s SDS arrives in English, in the 16-section format.

Section 1 itemOn the supplier’s SDSWhat the U.S. importer needs
Product identifierThe producer’s trade nameThe identifier on the label the importer ships. If the importer relabels under its own name, the SDS changes too.
Responsible partyThe producer’s name and European addressThe importer’s name and U.S. address. The producer can be listed as well, in Section 1 or Section 16.
Telephone numberA number with a foreign country codeA U.S. number that is answered, in English.
Emergency phone numberA foreign emergency lineA U.S. emergency number.
Recommended useA broad industrial descriptionThe uses the importer supports, with any restrictions.

The name and address on the shipped container label must match those on the SDS. The remainder of the supplier’s SDS must also be reviewed for compliance with U.S. regulations, as European classifications do not meet HazCom requirements. Our supplier SDS revision checklist outlines what to verify before incorporating supplier information into your own document.

Common Section 1 mistakes

  • Listing only a foreign address or phone number as the contact. This should be the first item checked for imported products.
  • Using a product name that does not match the label. Abbreviations, grade suffixes, or rebranded names disrupt cross-referencing.
  • Outdated contact details. Acquisitions, relocations, or phone system changes can result in obsolete names and inactive numbers on current SDSs.
  • An emergency number that is not answered. Test the number. If it is not staffed at all times, clearly state its hours of operation.
  • Listing the SDS service as the responsible party. A contracted company may serve as a contact but cannot be designated as the responsible party.
  • A recommended use that conflicts with other sections of the SDS. Uses listed in Section 1 must be supported by controls in Sections 7 and 8.
  • Inconsistent names and addresses between the SDS and the label. The directive requires these to be identical.

A repeatable Section 1 workflow

  1. Use the product identifier from the approved label artwork, not from memory or sales materials.

  2. List product codes, synonyms, and former names under other means of identification.

  3. Specify the recommended use and any restrictions, and verify consistency with Sections 7 and 8.

  4. Confirm the responsible party’s legal name, U.S. address, and an active U.S. telephone number.

  5. Ensure the emergency number is a U.S. number. Call to verify it is answered. If not staffed at all times, specify its hours.

  6. For imported products, replace or supplement foreign contact details. Move the foreign manufacturer to Section 16 if needed to avoid confusion.

  7. Verify that the name and address match the label, and that the product identifier matches the customer-facing product list.

  8. Review Section 1 whenever there are changes to the company name, address, phone system, emergency provider, or product name.

Cross-check Section 1 against the rest of the SDS

Compare withWhat must agreeReview question
The labelProduct identifier, name and addressWould a worker holding the container find this SDS?
The chemical inventoryProduct identifierDoes the name on the employer’s list match?
Sections 7 and 8Recommended uses and the controls for themAre the stated uses covered by the handling and exposure advice?
Section 4Emergency number and the first-aid advice to callCan the number give emergency information for this product?
Section 14 and shipping papersEmergency response number for transportDoes the transport number meet the DOT rule?
Section 16Foreign manufacturer details, revision dateIs supplemental contact information placed where it will not confuse?

The SDS Cross-Check Checklist puts these checks, and the ones for the other 15 sections, into a four-page PDF.

Section 1 outside the US

The same product needs a different Section 1 in each market, because each one wants a supplier it can reach.

RegionWhat Section 1 asks for
CanadaThe initial supplier, meaning the Canadian manufacturer or importer. The emergency number does not have to be Canadian, but any limits on it, such as hours or languages, must be stated.
EUFour numbered subsections, 1.1 to 1.4. Section 1.1 must say if the substance is a nanoform and give the Unique Formula Identifier where one is required. Section 1.4 usually carries national poison centre numbers.
UKA supplier based in Great Britain.

OSHA’s 2018 letter also accepts a combined US and Canada SDS, provided it meets every HazCom requirement and the added information does not contradict the required content. See US, EU and Canada SDS requirements.

How Valenc does it

In Valenc, both the SDS and GHS label are generated from the same product record, ensuring consistency in the product identifier. Each supported region, including the US, Canada, Mexico, the EU, and the UK, follows its specific format. All documents require human approval before publication.

To view this process with your products, request a demo. If you prefer to begin with your existing documents, our free SDS indexing service extracts fields from up to 100 SDSs and provides them in a spreadsheet.

Frequently asked questions

What is in Section 1 of an SDS?

Identification. It gives the product identifier, other means of identification, the recommended use and restrictions on use, the responsible party’s name, U.S. address and U.S. telephone number, and an emergency phone number.

Does the address on a US SDS have to be in the United States?

Yes. Appendix D requires a U.S. address and a U.S. telephone number for the manufacturer, importer or other responsible party.

Who is the responsible party on an imported product?

The importer, meaning the first U.S. business that receives the product. The foreign manufacturer can be listed as supplemental information.

Does the emergency phone number have to be 24 hours?

OSHA does not require it for the SDS. DOT does require a number monitored at all times for hazardous materials in transportation, so many companies use one number that meets both.

Can a P.O. Box be used as the address?

Yes. OSHA’s inspection directive accepts a mailing address, including a P.O. Box, or the company’s physical location.

Does the product name on the SDS have to match the label?

Yes. Section 1 requires the product identifier used on the label, and the identifier must allow the label, the SDS and the chemical inventory to be cross-referenced.

See the SDS and the GHS label generated from the same product record, using your own products.

← Back to all posts